Step and Repeat Banners

When used indoors, the Step and Repeat banner does not require any anchoring methods. The design of the frame allows for stability on even surfaces. It’s important to note that, if used outdoors, there are no manufactured anchor points where a rope can be used to tie the Step and Banner frame to an object.

Proper displaying and caring for your banner will prevent any fading to the design. Indoor use of the banner will protect the design from fading over time. Only prolonged and direct exposure to the sun will adversely impact the printing of your fabric banner.

The design is permanently dyed into the fibers of the fabric banner using a heat transfer process, which provides increased longevity and scratch resistance. Scratching of the design is unlikely without damage to the fabric itself. In any case, proper care, displaying, and storing of the banner will protect your fabric from snagging or tearing.

To assemble your Step and Repeat banner there are a few simple steps you must follow. These steps are outlined on an instruction sheet that comes with your purchase. If for some reason this is missing we’ve outlined the process below. While assembly and take down can be done by a single person, we recommend that at least two people work together to set up your Step and Repeat banner. With two people assembly takes no longer than 5-10 minutes. Each Step and Repeat banner will come with 6 poles and 2 metal stands or bases. Also included is an allen wrench, 4 plastic head bolts and two screws. The poles are labelled with a small plastic decal with letters on them. These consist of 2 “A-B” poles, 2 “C-D” poles and 2 “A-C” poles. The former two (“A-B” and “C-D”) are the horizontal poles. The latter will be the vertical poles of your frame. The first step is to connect the top horizontal poles (A-B) by connecting the two “B” ends of the poles. Simply press the small silver button down on one “B” end of the poles. This will then slide into the other “B” end of the top pole and click into place. Once clicked into place the “A” ends can be loosened and extended to the proper width of your banner. The bottom poles are connected in the exact same fashion as the top ones. These are the “C-D” poles with the “D” end having the locking button and hole and the “C” ends having the adjustable portion of your frame. The vertical poles are indicated by the A-C stickers. These do not have a locking mechanism on either end of the poles. Rather, the bottom has a threaded hole to attach to the base using the allen wrench and screw. This pole then has two places to loosen and extend the pole to the full height needed. Once fully extended and attached to the base ensure the holes at the top and bottom of the pole face inwards in order to attach your horizontal poles to the vertical ones. Before attaching your horizontal poles to the two vertical ones, put the two horizontal poles through the provided pole pockets on the backside of your banner. Make sure to carefully pull the banner over the loosening grips to ensure no ripping of the pole pocket. We recommend putting the poles through the pockets on the ground. Once your horizontal poles are put through the pockets you need to attach them to the vertical poles and bases previously assembled. Using the four provided plastic head screws, firmly tighten the top and bottom of each side of your frame. We recommend you do this all on the ground for easiest assembly. Once fully assembled, and with the help of another person, stand up your backdrop banner with the two bases sitting on a flat, solid surface. You may need to adjust the width of your frame by shortening or lengthening the top and bottom of the horizontal poles. We recommend making adjustments to the top and bottom poles of the same side of the banner for the easiest assembly. The vertical poles can also be adjusted in the same fashion if the height needs adjustment.

We recommend storing your backdrop frame and banner in the carrying case that is included when purchasing the backdrop. This case is designed to hold all 6 poles and both bases in a secure, easy-to-store case. Though the banner does not ship within the carrying case, it is possible to carefully fold the banner to fit within the case for both travel and storage.

We suggest using a handheld steamer to remove any creases that may be present on your banner. You can also use an iron on a very low heat setting to remove wrinkles.

For simple dirt removal, you can clean your banner using a wet cloth. This will remove most surface dirt that could accumulate on the banner.

Polyester fabric is also suitable for use in a washing machine on a low spin cycle using cold water. When using a washing machine, avoid heavy detergents and bleach. We do not recommend using a tumble dryer to dry the banner. Instead, let the banner air dry completely before folding for storage or before displaying.